![]()
Please run "Ultra Blu-ray advisor” to see if all "Pass”.ĥ. Go to Control Panel > Hardware and sound > Sound and select "HDMI output”. #SOUND RESCUE TERRATEC SERIAL DRIVER#Download the driver from the following link:ģ. Press "F10” to save and exit the BIOS setup screen.Ģ.ěoot into O/S. Go to Advanced > CPU Configuration and enable "Software Guard Extensions” in BIOS setting. When the system boots up, press "F2” to enter UEFI setup screen. Playback Software: Power DVD 14 (from Pioneer Ultra HD Blu-ray Drive)ġ. Receiver / decoder: Onkyo TX-NR 747 or other receiver supports HDCP 2.2 Please make sure that you connect the USB drive to the USB BIOS Flashback port.Ģ.ěIOS Flashback button (BIOS_FB1, see p.9, No. *If the LED light turns solid green, this means that the BIOS Flashback is not operating properly.ġ. Wait until the LED stops blinking, indicating that BIOS flashing has been completed. Press the BIOS Flashback button for about three seconds. Step 7.Ĝonnect your USB drive to the USB BIOS Flashback port. *There is no need to power on the system. Then turn on the AC switch of the power supply. #SOUND RESCUE TERRATEC SERIAL INSTALL#Install the 24 pin power connector to the motherboard. Rename the file to "creative.rom” and put the file on root directory #SOUND RESCUE TERRATEC SERIAL ZIP#Step 4.Ĝopy the BIOS file to your USB flash drive and extract BIOS file from the zip file. #SOUND RESCUE TERRATEC SERIAL PC#Go to This PC → Right click on the mouse → Select Format → Select FAT32 → Start ![]() If the USB drive is not FAT32 format, please create an USB flash with FAT32 format. Go to This PC → Right click on the mouse → Select Properties → File system Please make sure that the file system of your USB flash drive is FAT32. Step 1.ĝownload the BIOS P1.30 or later version from ASRock's website If it is not detected please clean the golden finger of the graphics card with a rubber (pencil eraser) and reinstall the card. Then wait for the system to detect the device.ģ. If it is not, please shut down the system and press the power button to boot the system again. Please install one graphics card and make sure it can be recognized under device manager. Please double check if the system power is enough for the whole system.Ģ. The single GPU systems typically draw about 200W, the system will need adequate power for whole system. Power supply vendors suggest users to use only one power supply per system.ġ. Because the second power supply will only supply 12V voltage to the graphic cards, it can cause power loading imbalance. The second power supply should only be connected to some graphics cards (12V). The first power supply has to be connected to the motherboard (12V, 5V and 3.3V) and some of the graphics cards (12V). Normally the power supply will provide 12V, 5V and 3.3V power to the motherboard.īut in a mining system with multiple power supplies the situation is different. When using (close to) 13 graphics cards, you will probably have to use 2 power supplies. If you are using PCIe riser cards with a Molex connector, please use maximum two Molex connectors on each power cable. We recommend choosing PCIe riser cards with 6-pin power for the mining system.ģ. Or take the graphics cards off the riser cards and install them on the riser cards again.Ģ. Please double check if the graphics cards are installed properly on the riser cards. Please refer to the following three parts to check your system.ġ. The riser cards, power supply, graphics cards and even the OS are all key points for the system. If some graphics cards are not recognized by the system, it is not necessarily related to only the motherboard but also to other components. System is waking up from S4 state (S4=Hibernate) System is waking up from S3 state (S3=Sleep) System is entering S5 state (S5=Soft power off) ![]() System is entering S4 state (S4=Hibernate) Please try re-installing the keyboard and mouse. The keyboard and mouse could not be recognized. If the problem still exists, please try installing the graphics card in other slots or try other graphics cards. Please clear CMOS and try re-installing the graphics card. ![]() The graphics card or iGPU could not be recognized. Please check if the CPU is installed correctly and then clear the CMOS. Please see the diagram below for reading the Dr. Debug is used to provide codes that represent different errors that your system has encountered. U kunt deze logboeken eenvoudig (met één klik op de knop "Verwijderen" in Revo Uninstaller Pro) gebruiken om programma's van uw computer te verwijderen.Dr. Het is een database bestaande uit getraceerde logboeken voor geïnstalleerde programma's die zijn opgeslagen op onze website, opgesteld en onderhouden door het team van Revo Uninstaller Pro. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |